Some years back---I had an older lady (widow)---that contacted us regarding her LG dryer.
Her complaint was that the laundry was not dry at the end of the cycle.
Also---the cycle run time/duration was rather short (cycle ended far earlier than initial time displayed).
In her case---she does not wash/dry large loads at all---and rarely does she even have medium sized loads to wash.
On LG dryers---the MOISTURE SENSOR ("bars") are located at the front of the dryer---on the LINT FILTER HOUSING.
If the dryer is dead-level---which hers was---a small load of laundry will tumble in the GIANT DRUM and very erratically come into contact with the MOISTURE SENSOR.
By raising the REAR LEVELING LEGS about an inch---this forced the tumbling small load of laundry to remain at the *front* of the dryer---continually falling/contacting the MOISTURE SENSOR.
On dryers (other brands) in which the sensors are positioned at the rear/back of the drum---simply raise the *front* leveling legs to get the same result.
Technicians can demonstrate to the customer by running the dryer with 2 or 3 small pieces of clothing---laundry will either tumble at the rear of the drum or near the center (in an LG dryer--for example).
Explain to the customer---the MOISTURE SENSORs function and that wet/damp laundry *must* continually come into contact with the sensor (show the customer the location of the sensor).
After adjusting the legs---the customer/owner will notice the laundry moving toward the SENSOR location within 30 seconds of starting the cycle---and remain at that location in the drum for the duration of the cycle.
Question
My dryer will not get hot
asked 3 years, 10 months ago
User Name:
Anonymous
on DLE2050W
0out of 1found this question helpful.
1 answer
Hello and thank you for contacting us. I am sorry to hear that your dryer is not heating and I would be happy to assist in troubleshooting the issue.
First, you would want to make sure that your ducting [venting] does not exceed 16 feet; now, the way you determine if it does is that in addition to the stated length of the vent, you would need to add 10 feet for ever elbow [turn] in the ducting. If the vent is too long, the unit will not function as specified.
You would also want to check for any clogs in the ducting or filter of the unit.
Another troubleshooting would be with your sensor and dryer sheets. We do not recommend dryer sheets as they could coat the sensor cause drying to be less efficient.
If this does not help, you may need service. You can obtain service assistance by calling our Customer Service at 800-243-0000.
分享到微信
whois 说道: 无题
2015-03-11 08:28:55
xiaomai 说道: 无题
2015-03-11 08:29:22
谢谢。看哪里可以肯定？
我真不知道，对这一窍不通。想上网查，还看不到型号
型号一般在打开门的边框那里，如果你的租客是每次烘干清滤网的，应该是不会坏的。如果他没有定期清滤网的话的，或者很长时间清一次的话的，烘干机是是很容易坏的。
凌儿。 说道: 无题
2015-03-11 08:29:39
谢谢，这款似乎没有排气管
达达尼昂 说道: 无题
2015-03-11 08:30:17
本那比经略 说道: 无题
2015-03-11 08:31:28
谢谢，这款似乎没有排气管
不会吧，难道烘干机不产生热量不用排放？太先进了。。。:lol:
凌儿。 说道: 无题
2015-03-11 08:32:06
谢谢。看哪里可以肯定？
我真不知道，对这一窍不通。想上网查，还看不到型号
型号一般在打开门的边框那里，如果你的租客是每次烘干清滤网的，应该是不会坏的。如果他没有定期清滤网的话的，或者很长时间清一次的话的，烘干机是是很容易坏的。
谢谢您。我让租客晚上回来时再看看型号。
再具体问问
凌儿。 说道: 无题
2015-03-11 08:33:01
谢谢，这款似乎没有排气管
不会吧，难道烘干机不产生热量不用排放？太先进了。。。:lol:
我好像有这个印象。
凌儿。 说道: Re: 求助，烘干机罢工了
2015-03-11 08:34:14
There is a solution---and it's a very simple one.
Some years back---I had an older lady (widow)---that contacted us regarding her LG dryer.
Her complaint was that the laundry was not dry at the end of the cycle.
Also---the cycle run time/duration was rather short (cycle ended far earlier than initial time displayed).
In her case---she does not wash/dry large loads at all---and rarely does she even have medium sized loads to wash.
On LG dryers---the MOISTURE SENSOR ("bars") are located at the front of the dryer---on the LINT FILTER HOUSING.
If the dryer is dead-level---which hers was---a small load of laundry will tumble in the GIANT DRUM and very erratically come into contact with the MOISTURE SENSOR.
By raising the REAR LEVELING LEGS about an inch---this forced the tumbling small load of laundry to remain at the *front* of the dryer---continually falling/contacting the MOISTURE SENSOR.
On dryers (other brands) in which the sensors are positioned at the rear/back of the drum---simply raise the *front* leveling legs to get the same result.
Technicians can demonstrate to the customer by running the dryer with 2 or 3 small pieces of clothing---laundry will either tumble at the rear of the drum or near the center (in an LG dryer--for example).
Explain to the customer---the MOISTURE SENSORs function and that wet/damp laundry *must* continually come into contact with the sensor (show the customer the location of the sensor).
After adjusting the legs---the customer/owner will notice the laundry moving toward the SENSOR location within 30 seconds of starting the cycle---and remain at that location in the drum for the duration of the cycle.
凌儿。 说道: 无题
2015-03-11 08:34:55
早上好，谢谢帮顶
本那比经略 说道: 无题
2015-03-11 08:43:53
谢谢，这款似乎没有排气管
给你找到这个
Question
My dryer will not get hot
asked 3 years, 10 months ago
User Name:
Anonymous
on DLE2050W
0out of 1found this question helpful.
1 answer
Hello and thank you for contacting us. I am sorry to hear that your dryer is not heating and I would be happy to assist in troubleshooting the issue.
First, you would want to make sure that your ducting [venting] does not exceed 16 feet; now, the way you determine if it does is that in addition to the stated length of the vent, you would need to add 10 feet for ever elbow [turn] in the ducting. If the vent is too long, the unit will not function as specified.
You would also want to check for any clogs in the ducting or filter of the unit.
Another troubleshooting would be with your sensor and dryer sheets. We do not recommend dryer sheets as they could coat the sensor cause drying to be less efficient.
If this does not help, you may need service. You can obtain service assistance by calling our Customer Service at 800-243-0000.
应该是有排气管的。。。